张恒;郭艳;
ZHANG Heng;GUO Yan;SCEGC No.2 Construction Engineering Group Co., Ltd.;College of Architecture and Surveying, Shaanxi College of Communications Technology;

• 1:陕西建工第二建设集团有限公司
• 2:陕西交通职业技术学院建筑与测绘工程学院

摘要(Abstract)：

为更好推广ADG钢管模板支架在工程中的应用，对西安交通大学科技创新港科创基地1标段2号楼工程进行研究，首先确定模板支撑架体设计方案，分析长陡坡屋面高支模施工过程中的抗侧移设计要点，计算并设计坡屋面模板支架抗侧力，并设计坡屋面高度超过8m时的模板支架，确定模板支架基本参数后，建立模板支架模型，对坡屋面混凝土浇筑顺序进行数值模拟，以分析对高支模架承载力的影响，最后提出坡屋面施工时不同截面尺寸梁底部的模板支架顶撑设计方法，并验证分条对称浇筑坡屋面混凝土有利于保证模板支架承载力和稳定性。
To popularize the application of ADG steel pipe supporting system in civil engineering, the on-site application in the No.2 building project of the first bid section of the Xi'an Jiaotong University Science and Technology Innovation Base is taken as the research object. Firstly, the design scheme of formwork support frame is determined, and the key points of anti-lateral displacement design in high formwork construction of long and steep slope roof are analyzed. Secondly, by designing the anti-lateral force of slope roof formwork support and that with slope roof height more than 8 meters, the basic parameters of it are determined, thus the formwork support model is established. Then, through numerical simulation of concrete pouring sequence of slope roof to analyze its influence on the bearing capacity of high support formwork, it proposes the design method of formwork support at the bottom of beams with different section sizes during slope roof construction. It is verified that the symmetrical pouring of slope roof concrete is beneficial to the bearing capacity and stability of formwork support.

关键词(KeyWords)： 钢管模板支架;坡屋面;高支模;稳定性;承载力
steel formwork support;slope roof;high supporting system;stability;bearing capacity

Abstract:

Keywords:

基金项目(Foundation):

作者(Authors): 张恒;郭艳;
ZHANG Heng;GUO Yan;SCEGC No.2 Construction Engineering Group Co., Ltd.;College of Architecture and Surveying, Shaanxi College of Communications Technology;

参考文献(References)：

• [1] 余宗明.新型脚手架的结构原理及安全应用[M].北京：中国铁道出版社，2001.
• [2] YUE F,YUAN Y,LI G Q,et al.Wind load on integral-lift scaffolds for tall building construction[J].Journal of structural engineering,2005,131(5):816-824.
• [3] 顾明剑.超高大跨度承重支撑体系设计施工研究[D].上海：同济大学，2006.
• [4] 回忆.ADG装配式脚手架的应用性能研究[D].北京：北京交通大学，2008.
• [5] 胡长明.扣件联接钢结构的试验及其理论研究[D].西安：西安建筑科技大学，2008.
• [6] 姜旭，张其林，顾明剑，等.新型插盘式脚手架的试验和数值模型研究[J].土木工程学报，2008(7):55-60.
• [7] 程骥，龚晋德，陈亚丽.不同工况下基于MIDAS/FEA模型的脚手架可调托撑托板计算分析[J].施工技术，2021,50(2):63-65.
• [8] 贾建国.ADG插销式脚手架稳定承载能力的研究分析[D].西安：西安建筑科技大学，2014.